Before we begin, The Protos X EtherNet/IP bus coupler will only work with an implicit
Ethernet/IP client. You will need to install the latest version
of Protos X Configuration software. Then you will need to connect a powered Protos X system
to your PC using this cable. Open up the configuration software
Select Tools and then connect Now you should see a full listing of the modules
you have connected.
To set the IP address of this adapter, select Tools and then coupler configuration. Enter
in your IP address and then you will see the resultant Dip switch settings that that you
will need to apply to your bus coupler. Make the changes to your dip switches and then
select Ok. You will then be asked to reboot the coupler. Select Ok.
Here will be the Assembly instance information you will need to setup your client.
Notice that the top is listed in Bytes but the Format data is in 16 bit words. By selecting
the Plus sign here we can see that input word 1 and input word 2 are mapped to the coupler,
same with the first 2 output words. If you continue down the tree of modules, it will
show which words are mapped to each module. For the detailed purpose of each word please
consult the Protos X manual.
Now let's take this assembly instance data and apply it to a Productivity CPU.
Open up your Project. Open up the Hardware Configuration and then select the EtherNet/IP
Tab. Drag the Generic Client into the Grey area. Now, you can place an induvial tag for
each of these elements or you can check the box Use Structure. This will create a structure
of tags that contain all of these elements. I am going to select the Use Structure and
give it the following name. Now, I'm going to give the device a name. Type in the IP
address that we configured in the Coupler configuration. Now the TCP port number for
the Protos X coupler will always be 44818. Click on the Green cross and select add I
O messaging. These tags will also be part of the original Structure created above. This
tag, in particular, will enable the Reads and write at the RPI that we select for each.
Here you see that there are now 3 tabs. Lets' start with the Input data block
From this information we see the assembly instance should be 101.
The data array data type must match the data size of the input data block. Now from the
information we see here, we see that the data blocks are in 16 bit words and there are 27
words in total. So we need to create a data array of a 16 bit type, and has at least 27
columns. SO type in the name of the Data block you want to create and when you try to select
the Number of elements you will then be asked to create this array. Select the Data type
as 16 bit unsigned and increase the number columns to 27. Select ok. And then Increase
the Number of elements to 27. Now select the output tab.
The Assembly instance is 102. I am going to name my output data array as the following
and when I select the number of elements I will be asked to create the array. Change
the data type, once again, to 16 bit unsigned and the column size, should also be 27. Click
ok. Change the number of elements to be 27. Now to setup the Configuration word
Enter the Assembly instance of 100. I am going to enter the following data array
and when I click on number of elements this dialog will show up. Change the data type
to 16 bit unsigned and the Columns can remain as 1. Select ok. And then number of elements
can remain as zero. When we select Ok here we will be completing
the structure for this device Now that the structure has been Completed,
let's open the client once more and select Monitor. This will create a Dataview tab to
control and view all of the tags associated with this setup.
Now we just need to transfer this this project to the CPU.
With the project transferred and the PLC in Run, let's open up the Dataview to quickly
test this setup. Select to edit the Enable bit and then select
to send the edit. Now you should see status indication of the
connection. If you have any questions about the Protos
X please contact AutomationDirect's free award winning support team during regular
business hours. They will be happy to help. Click on this video to learn more about AutomationDirect's
many support options, click here to learn more or see more videos on our many products,
and be sure to click here to subscribe to our YouTube channel.
For more infomation >> Former KC radio host helps mother evacuate Florida - Duration: 2:03. 
For more infomation >> Bí mật tìm nguồn tin hot làm video tin tức nước ngoài kiếm tiền youtube - Duration: 35:41. 
For more infomation >> Las Noticias de la mañana, jueves 7 de septiembre de 2017 | Noticiero | Noticias Telemundo - Duration: 5:20. 
For more infomation >> SBTV II Hot Boy Tùng Maru - Duration: 2:12. 
For more infomation >> Tin Hót ► U18 Việt Nam 8-1 U18 Brunei: Chiến thắng hủy diệt - Duration: 2:34. 
For more infomation >> U18 Việt Nam 8-1 U18 Brunei || SÉT TENNIS || - Duration: 5:22. 
For more infomation >> "Neymar está meando desde el trampolín" - Duration: 2:03. 
For more infomation >> Thánh Nấu Ăn P5 || Bò Nướng Lon Coca Cola || Tưởng Không Ngon Ai Ngờ Ngon Không Tưởng - Duration: 11:16. 
Không có nhận xét nào:
Đăng nhận xét