Again, we are lucky to have the inestimable help of David de Fox,
that today he is going to tell us things about the remote control of the fit 4 cartridges, no
Is it like that, David? This is Jesus! Today, all 4 2018 fit forks and 2019 models
can have two system logics Remote: Push to Lock, press to block, and
Push to unlock, press to unlock. And today, with a FOX tool, let's go
to show how to adjust it. Very good, well I leave you with him and learn about FOX.
We are going to make the adjustment in a cartridge Fit 4 using our tool
FOX official in a system with logic push to unlock First we are going to
explain what is the logic Push to unlock and Push to lock, and for that,
we have both here on the table remote kits. As you can see, what
turn the cable in the orientation of the cable is to the left would be the
Push your unlock, the one that does it to the right would be the Push to lock,
are two logical fox offers us from the year 2018 also in this campaign of
2019, on all Fit4 cartridges remote systems.
This one on the right, the fork will be permanently blocked, and only when
press the control of the handlebar will unlock It will be totally what
opposite in the one on the left, in the Push to Lock, press to block the
hairpin, will always be open and when we press the handlebar control the
fork will lock. It is important that you know that the blocking logic that
you can install in your hairpin is linked by the butterfly that
have the fit 4 cartridge installed your hairpin How to check what
butterfly comes, as simple as entering in the help section of the web: ridefox.com
and put your ID code, and you will give all the information of that butterfly.
It is possible to replace it to change the logic Push to Lock or Push to Unlock,
even from three positions to two positions. To make the adjustment of these
systems in the fork we are going to need this tool, which will have
two pieces one for each kit, now we will see about the bike how
use this tool and always these kits will be united to our command
of two FOX positions, which may be work with the output of a cable only
for the fork, or two cables for fork and shock absorber.
In the event that we have a fork how is this fantastic 32 step cast that is not
they have command to the handlebar we could install it of course. We can
refer us to previous videos Mammoth where we did the transformation of
cartridges from non-remote systems to remote.
The problem will come when we let's install one of these kits in one
fork with original cartridge fit 4 2018 2019 of
three positions as are all not remote forks.
The fork will stay three positions and we will need to use a
command of three positions, if we want to use a command of two
positions will have to be done internal transformation replacing the
Butterfly blocking by one of two positions. Unfortunately this
you can not do it at home and it will have to be done in a technical service
official or in any of the workshops Mammoth. For the installation of
Push to Unlock systems, it's really easy, we will only have to use the key
fixed from 8 put the fork in position blocked, turning to the direction of
clock hands.
Then with the help of our tool,
Push to unlock,
we will place in this position the sense clockwise,
we'll give it a spin and it'll stay preloaded and blocked, once with the
prepared piece,
we will slide it with the cable orientation completely
attached to the pipe the address
and we will have prepared the fork. To end,
we just have to put the regulator compression at low speed and
screw it, and we will have totally the fork ready to connect the
cable. To install the remote system push to
lock, press to lock in a cartridge fit 4 2018 2019, we will start by opening in
the cartridge in the open position up your top,
we should have the correct kit, where you see that the orientation of the cable is
to the right. We will have to choose if we put it with the
cable exit towards the one or towards 7, which are the two positions
official and authorized by FOX. Before we have to recharge the pier with
our FOX tool. We will insert the tool, and the sense
counter-clockwise,
we will preload it and we will have it prepared. And now,
we will simply slide it up to the position that we have
chosen one.
To finish we will put the compression regulator of
low speed.
We will press it ...
and we will have the fork ready for connect the cable. To connect the cable,
In both Push to Lock and Push to Unlock cases, the handlebar lever has to
be without pressing, in sleep mode.
We passed the cable and we will connect everything perfectly,
and we will press the prisoner.
And so we will have finished our connection. Verify with the command
that works perfectly ... and we just it will be cut the cable.
Thank you very much David again for explain to us so thoroughly everything
that you explain to us in the videos. You're welcome, Jesus. Thanks for being here...
and well, come on, today we are going to finish with a smile to see if it's funny
David, I did not listen to her before. He says... How are you doing about the disorder?
personality? And it says ... Do not ask me, that takes the other one! Thanks for
listen to us and see you in the next video!
Ciao!
For more infomation >> Amerikanische Pancakes | Rezept #188 - Duration: 4:22. 
For more infomation >> Apres le Coup de Chien 4K - TV Quiberon 24/7 - Duration: 1:38. 
Không có nhận xét nào:
Đăng nhận xét